NFPA 664: Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Fac

Available Discounts

 Members Save 10%

  •  
Save 15% with a Set!

  • Order now and save 15% on 2 or more formats.
Item #: NFPA_664
List Price: $0.00
2012 NFPA 664
Prior Years Prior Editions of NFPA 664
Quantity:

Revisions in the 2012 NFPA 664 increase protection of lives and property from fires and explosions in wood processing and woodworking facilities.

Updated to reflect industry changes, the 2012 NFPA 664: Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities presents the latest requirements for the construction, operation, and protection of industrial, commercial, or institutional facilities that process wood or manufacture wood products.

Many of the revisions were made for consistency with NFPA 68: Standard on Explosion Protection by Deflagration Venting, and NFPA 69: Standard on Explosion Protection Systems. In addition, changes were made to requirements for the efficiency of dust collectors for recycling of exhaust air for consistency with the Industrial Ventilation Manual published by ACGIH.

Top 2012 NFPA 664 changes include:

  • New procedures for handling 'deflagration hazard', including a new definition, a new methodology for determination of a deflagration hazard using settled bulk density to determine an allowable thickness for combustible wood, plus detailed Annex instructions on how to collect the dust sample for the new methodology
  • New section with requirements on hazard determination including access doors for inspection and fire department access of ductwork
  • Revised requirements for the use of explosion protection systems and deflagration venting on metal ducts located both indoors and outdoors
  • Reduction of the concentration criterion for allowing ducts to handle dusts without protection from 75 percent of the minimum explosible concentration (MEC) down to 25 percent of MEC to correlate with NFPA 69: Standard on Explosion Prevention Systems
  • Revised provisions for dust collectors with deflagration hazards to be equipped with a deflagration suppressions system
  • Revised criteria for deflagration relief vents on dust collectors
  • Revised requirements for recycling of air-materials separators exhaust into buildings
  • New Annex material on control system design for solid fueled burners

The 2012 NFPA 664 is a must for industrial, commercial, or detention and correction facilities that operate woodworking shops as well as wood processing facilities that manufacture wood products, those that process wood, creating wood chips, particles, or dust that occupy areas greater than 5,000 sq. ft. (465 sq. m), or those that have an aggregate dust collection flow rate greater than 1500 cu. ft. per minute (2549 cu m/hr.) In addition, this important Standard is useful for fire marshals, fire/building departments, and other AHJs which regulate the facilities and agencies that conduct inspections on these facilities. (Softbound, 70 pp., 2012)

NFPA® 664 Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities 2012 Edition

Chapter 1 Administration
1.1 Scope
1.2 Purpose
1.3 Application
1.4 Retroactivity
1.5 Equivalency
1.6 Units and Formulas
Chapter 2 Referenced Publications
2.1 General
2.2 NFPA Publications
2.3 Other Publications
2.4 References for Extracts in Mandatory Sections
Chapter 3 Definitions
3.1 General
3.2 NFPA Official Definitions
3.3 General Definitions
Chapter 4 General Requirements
4.1 Goal
4.2 Deflagration Hazard
4.3 Process Analysis
4.4 Management of Change
4.5 Designer and Installer Qualifications
4.6 Objectives
4.7 Compliance Options
Chapter 5 Performance-Based Design Option
5.1 General Requirements
5.2 Performance Criteria
5.3 Design Fire Scenarios
5.4 Evaluation of Proposed Design
5.5 Safety Factors
Chapter 6 Building Construction
6.1 Prescriptive Requirements
6.2 Compartmentation
6.3 Occupant Life Safety Systems Means of Egress
6.4 Special Requirements
Chapter 7 Prevention of Ignition and Control of Ignition Sources
7.1 Prescriptive Requirements
7.2 Hot Work
7.3 Electrical Systems
7.4 Hot Surfaces
7.5 Industrial Trucks
7.6 Lighting
7.7 Fuel-Fired Equipment
7.8 Lightning Protection
7.9 Static Electricity
7.10 Machines and Processing Equipment
7.11 Machinery Setup and Maintenance
7.12 Foreign Material
7.13 Friction
7.14 Fans
7.15 Spontaneous Ignition and Chemical Action
7.16 Propellant-Actuated Tools
7.17 Smoking
7.18 Portable Electric Equipment and Appliances
Chapter 8 Processes, Operations, and Special Systems
8.1 General
8.2 Particulate Conveying and Dust Collection Systems
8.3 Thermal Oil Heating Systems
8.4 Particulate Size Reduction Equipment
8.5 Panel Product Manufacturing Machinery
8.6 Dryer Systems
8.7 Spray Finishing
8.8 Dipping and Coating
8.9 Pollution Control Equipment
8.10 Storage
8.11 Hot Presses
8.12 Wood Scrap or Wood Waste Processing and Disposal
Chapter 9 Fire Protection
9.1 General Fire Protection
Chapter 10 Human Element
10.1 Objective
10.2 Inspection and Maintenance
10.3 Record Retention
10.4 Employee Training
10.5 Contractors and Subcontractors
10.6 Portable Appliances
10.7 Management of Change
10.8 Incident Investigation
10.9 Impairments of Fire Protection and Explosion Prevention Systems
10.10 Smoking
10.11 Hot Work
10.12 Emergency Planning and Response
Chapter 11 Housekeeping
11.1 General Requirements
11.2 Cleanup Methods
Annex A Explanatory Material
Annex B Explosion Protection
Annex C Informational Primer on Spark Detection and Extinguishing Systems
Annex D Conveying System Isolation
Annex E Automatic Water Spray Deluge Protection for Dryer Systems
Annex F Informational References
Index