NFPA 34: Standard for Dipping and Coating Processes Using Flammable or Combustible Liquids

Available Discounts

 Members Save 10%

  •  
Save 15% with a Set!

  • Order now and save 15% on 2 or more formats.
Item #: NFPA_34
List Price: $0.00
2011 NFPA 34
Prior Years Prior Editions of NFPA 34
Quantity:

Promote industrial fire safety with the 2011 NFPA 34: Standard for Dipping, Coating, and Printing Processes Using Flammable or Combustible Liquids.

NFPA 34 addresses dipping, roll coating, flow coating, printing, and similar processes using flammable or combustible liquids. Parallel to the requirements in NFPA 33 for spray application, this document provides rules for:

  • Proper location, design, and construction of dipping and coating equipment
  • Installation of electrical systems and control of ignition sources
  • Ventilation requirements
  • Handling of flammable liquids
  • Fire protection
  • Operations and maintenance

Major changes in the 2011 NFPA 34: Standard for Dipping, Coating, and Printing Processes Using Flammable or Combustible Liquids include:

  • Appropriate changes throughout the standard to address basic fire safety for printing operations
  • Amendments to the scope to include vapor degreasing processes and to exempt processes using only Class IIIB combustible liquids
  • A provision to prevent coating of workpieces whose surface temperature exceeds the boiling point of the coating material
  • Provisions to describe the hazardous (classified) areas around printing presses and ink reservoirs
  • A requirement for means to dissipate static electricity from nonconductive substrates
  • Maximum quantities of flammable and combustible liquids revised for consistency with NFPA 30: Flammable and Combustible Liquids Code.
  • Improved requirements for housekeeping and handling of impregnated rags and waste
  • A new requirement for solvent recovery systems to meet appropriate provisions of NFPA 30

Protect lives and work-in-progress. Mitigate fire and explosions hazards with the 2011 NFPA 34. (Softbound, 30 pp., 2011)

NFPA® 34 Standard for Dipping, Coating, and Printing Processes Using Flammable or Combustible Liquids 2011 Edition

Chapter 1 Administration
1.1 Scope
1.2 Purpose
1.3 Application
1.4 Retroactivity
1.5 Equivalency
1.6 Units and Formulas
1.7 Enforcement
Chapter 2 Referenced Publications
2.1 General
2.2 NFPA Publications
2.3 Other Publications
2.4 References for Extracts in Mandatory Sections
Chapter 3 Definitions
3.1 General
3.2 NFPA Official Definitions
3.3 General Definitions
Chapter 4 Location of Dipping, Coating, and Printing Processes
4.1 Scope
4.2 Separation
4.3 Locations Below Grade
4.4 Access to Means of Egress
4.5 Locations in Other Occupancies
Chapter 5 Design and Construction of Dipping, Coating, and Printing Equipment and Systems
5.1 Scope
5.2 General Requirements
5.3 Height Above Floor
5.4 Overflow Prevention
5.5 Liquid Level
5.6 Overflow Pipes
5.7 Bottom Drains
5.8 Salvage Tanks
5.9 Conveyor Systems
5.10 Control of Liquid Temperature
Chapter 6 Electrical and Other Sources of Ignition
6.1 Scope
6.2 General
6.3 Electrical Area Classification - Class I Locations
6.4 Areas Adjacent to Open Processes
6.5 Areas Adjacent to Enclosed Dipping and Coating Processes
6.6 Equipment and Containers in Ventilated Areas
6.7 Light Fixtures
6.8 Static Electric Discharges
Chapter 7 Ventilation
7.1 Scope
7.2 General
7.3 Performance Requirements
7.4 Make-Up Air
7.5 Routing of Exhaust Ducts
7.6 Recirculation of Exhaust
7.7 Materials of Construction
7.8 Support of Exhaust Ducts
7.9 Exhaust Duct Cross-Section
7.10 Exhaust Duct Access
7.11 Exhaust Fans and Drives
7.12 Drying Areas
Chapter 8 Storage, Handling, and Distribution of Flammable and Combustible Liquids
8.1 Scope
8.2 General
8.3 Storage in Process Areas
8.4 Transporting Liquids
8.5 Handling Liquids at Point of Final Use
8.6 Liquid Piping Systems
Chapter 9 Protection
9.1 Scope
9.2 General
9.3 Automatic Fire Protection Systems
9.4 Ventilation Systems
9.5 Notification and Interlocks
9.6 Automatic Fire Protection for Small Dipping Processes
9.7 Automatic Fire Protection for Enclosed Processes and Large Processes
9.8 Requirements for All Fire Protection Systems
9.9 Specific Requirements for Automatic Carbon Dioxide, Dry Chemical, and Clean Agent Systems
9.10 Specific Requirements for Water-Based Fire Protection Systems
9.11 Automatic Fire Protection for Printing Processes
9.12 Portable Fire Extinguishers
Chapter 10 Operations and Maintenance
10.1 Scope
10.2 General
10.3 Waste Containers
10.4 Inspection and Testing
10.5 Cleaning Operations
10.6 Combustible Dusts and Residues
10.7 Smoking
10.8 Hot Work
10.9 Solvent Distillation Units (Solvent Recyclers)
10.10 Solvent Recovery Systems
Chapter 11 Electrostatic Detearing Apparatus
11.1 Scope
11.2 General
11.3 Requirements for Electrical System and Components
11.4 Support of Workpieces
11.5 Manual Operations
11.6 Electrical Safety Requirements
11.7 Personnel Safety
11.8 Grounding Requirements
11.9 Signs
11.10 Drip Plates and Screens
Chapter 12 Training
12.1 General
Annex A Explanatory Material
Annex B Fire Record
Annex C Illustrations of Suggested Methods of Protection
Annex D Informational References
Index